![how to connect pentair screenlogic how to connect pentair screenlogic](https://demo.dokumen.tips/img/380x512/reader018/reader/2020020304/5c97966909d3f20d198c5b4f/r-1.jpg)
- How to connect pentair screenlogic install#
- How to connect pentair screenlogic serial#
- How to connect pentair screenlogic manual#
Use the supplied 12 inch cable to connect the ScreenLogic Interface indoor wireless transceiver to the ScreenLogic Interface Protocol adapter.
How to connect pentair screenlogic install#
To install the ScreenLogic Interface Wireless Connection kit: Mount the outdoor transceiver antenna near the IntelliTouch or EasyTouch Control System Load Center and connect the transceiver to the COM port connector located in the IntelliTouch or EasyTouch Control System Load Center.
How to connect pentair screenlogic serial#
ScreenLogic Interface Wireless Connection Installation Guide (this manual) ScreenLogic Interface Protocol Adapter (purchased separately) SERIAL CONNECTION Black Green Yellow Red LAN RESET Protocol Adapter Cable (for connection to ScreenLogic Interface Protocol Adapter (purchased separately) NOTICE: ID s on Indoor and outdoor transceiver must match Indoor transceiver ID NUMBER Outdoor transceiver Outdoor Cable (white - 10 ft.) AC transformer 4X 2X 2X 4X Outdoor Transceiver enclosure Mounting hardware ScreenLogic Interface Wireless Connection Kit ContentsĤ 1 Summary installation steps The ScreenLogic Interface connection diagram on page 2 shows the transceiver locations and connections. cable, provided in kit with enclosure and mounting hardware. One ScreenLogic Interface outdoor wireless transceiver with 10 ft. One ScreenLogic Interface indoor wireless transceiver with AC power adapter and one foot connection cable with attached plugs. Wireless Connection Kit Contents The following items are included in the Wireless Connection kit. This wireless connection eliminates the existing hard wire connection from inside your home to the equipment pad. For more information, call Customer Support (880) The transceivers provides a wireless connection between the ScreenLogic Interface Protocol adapter and the IntelliTouch or EasyTouch Control System Load Center located at the equipment pad. Transceivers are replaced as a matched pair. The ID numbers on each transceiver must be the same number to function correctly. Note: The transceivers ship from the factory as a matched pair. For ScreenLogic Interface system operating instructions, refer to the ScreenLogic Interface User s Guide (P/N )ģ LABEL P/N P/N ScreenLogic Interface Wireless Connection Kit The ScreenLogic Interface Wireless Connection interface consists of an indoor and outdoor wireless 2.4 GHz transceiver.
How to connect pentair screenlogic manual#
In this Installation Guide Use the information in this manual for installing the ScreenLogic Interface Wireless Connection kit contents.
![how to connect pentair screenlogic how to connect pentair screenlogic](https://www.poolsupplyunlimited.com/Products/Large/144760_0_201772911485.jpg)
Modifications not expressly approved by the party responsible for FCC compliance could void the user s authority to operate the equipment. Consult the dealer or an experienced radio/tv technician for help. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Increase the separation between the equipment and receiver. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. However, there is no guarantee that interference will not occur in a particular installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
![how to connect pentair screenlogic how to connect pentair screenlogic](https://www.poolsupplyunlimited.com/Products/Product2/144760_0_2017729122925.jpg)
8 FCC Regulatory Safety Notice - This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. 3 Step 2: Connect the Indoor Wireless Transceiver to the ScreenLogic Interface Protocol Adapter. 2 Step 1: Mount the Outdoor Wireless Transceiver and Connect to the IntelliTouch or EasyTouch Load Center. 1 ScreenLogic Interface Wireless Connection Kit Contents. 6502) Fax: (805) Web sites: visit and Related manual: ScreenLogic Interface User s Guide (P/N ) Contents Overview. 1 SCREENLOGIC INTERFACE WIRELESS CONNECTION KIT FOR INTELLITOUCH AND EASYTOUCH CONTROL SYSTEMS INSTALLATION GUIDE IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONSĢ Technical Support Sanford, North Carolina (8 A.M.